meta data for this page
  •  

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision		Previous revision
groups:mg:temperature_controller [2018/05/08 08:35] – rholstgroups:mg:temperature_controller [2018/06/01 14:32] (current) – [In loop stability] rholst
Line 5: Line 5:
 ===== Current Setup - Rack Mount===== ===== Current Setup - Rack Mount=====
  
-{{:groups:mg:meerstetter_temperature_controller_rack_mount_front_view.jpg?300|}} {{:groups:mg:meerstetter_temperature_controller_rack_mount_back_view.jpg?300|}} {{:groups:mg:meerstetter_temperature_controller_rack_mount_inside_view_3.jpg?350|}}   +{{:groups:mg:meerstetter_temperature_controller_rack_mount_front_view.jpg?200|}} {{:groups:mg:meerstetter_temperature_controller_rack_mount_back_view.jpg?200|}} {{:groups:mg:meerstetter_temperature_controller_rack_mount_inside_view_3.jpg?300|}}   
-{{:groups:mg:meerstetter_temperature_controller_rack_mount_inside_view_2.jpg?350|}}+{{:groups:mg:meerstetter_temperature_controller_rack_mount_inside_view_2.jpg?300|}} 
 + 
 +  * **Switch**: controls connection between lab power supply and meerstetter 
 +  * **Power LED**: on = power on, off = power off 
 +  * **Status LED**: on = Temperature at setpoint, blinking = ramping to setpoint, off = power off or error 
 +  * **USB**: connection to PC, see [[groups:mg:meerstetter|Meerstetter wiki entry]] for more information 
 +  * **SUB D-9**: male connector, connects to [[groups:mg:laserdiode_mount|laser mount]] 
 +  * **Tuchel socket**: connection to 5-24V @ 4A max 
 + 
 +^ Socket  ^ Pin Name   ^ Connected To  ^ Explanation                       ^ 
 +| X1      | VIN        | XLR Plus      | connections for the power supply  | 
 +| :::     | GND        | XLR GND       | :::                               | 
 +| :::     | RES2       | LED Anode     | status LED                        | 
 +| X2      | OUT +      | SUB D Pin 4   | TEC (+)                           | 
 +| :::     | OUT -      | SUB D Pin 5   | TEC (-)                           | 
 +| :::     | OBJ T° UA  | SUB D Pin 3   | NTC (-)                           | 
 +| :::     | OBJ T° UB  | SUB D Pin 2   | NTC (+)                           | 
 +| :::     | Shield     | SUB D Pin 9   | GND for shield of cable           | 
 + 
 +The output of the Meerstetter is filtered as shown [[groups:mg:meerstetter#output_filter|here]]. 
 + 
 +For the configuration file of the Meerstetter refer to ''\\AFS\iqo.uni-hannover.de\projects\magnesium\Projekte\PTB Ultrastable laser\Laser at IQO\meerstetter rack einschub'' 
 + 
 +==== In loop stability ==== 
 + 
 +The Meerstetter stabilises the 1560 nm rio planex laser diode running at 123.5mA to the target temperature with a standard deviation of ca. 0.23 mK. 
 + 
 +{{:groups:mg:meerstetter_rack-mount_in_loop_temperature_vs_time.png?400|}}{{:groups:mg:meerstetter_rack-mount_in_loop_temperature_stability.png?400|}}{{:groups:mg:meerstetter_rack-mount_in_loop_temperature_spectrum.png?400|}} 
 ---- ----
  
Line 74: Line 102:
 | blinking     | ramping towards target temperature | | blinking     | ramping towards target temperature |
 | off          | error/Meerstetter is off           | | off          | error/Meerstetter is off           |
- 
- 
-To add another status LED to the Meerstetter, you can follow this [[groups:mg:meerstetter#status_leds|step-by-step guide]] 
- 
-==== Other Modifications ==== 
- 
-<note important> What's the meaning of this? </note> 
- 
-On the back side of the circuit board at these two places, two soldering points have to be soldered together, so that 2 wires can be used to connect the NTC. \\ 
-{{:groups:mg:project_ptb-cavity:meerstetterplatine.jpg?400|}}