meta data for this page
Translations of this page:
- en
This is an old revision of the document!
Labelling of the cables
Labelling of the T-Regler cable
Peltierelemente werden an der Oberseite warm, wenn Output-Pins 3,2 sowie 1 an positiver Spannung angeschlossen ist.
Benutzt wird der Kabeltyp:
- Für Peltierelemente: LAPP Kabel Stuttgart Unitronic LIYCY 8×0.14; Schirmung von alle Adern gleichzeitig
- Für In-loop-NTC´s: LAPP Kabel Stuttgart Unitronic LIYCY 6×0.14; Schirmung von alle Adern gleichzeitig
- Für Out-of-loop-NTC´s: LAPP Kabel Stuttgart Unitronic LIYCY 16×0.14; Schirmung von alle Adern gleichzeitig
| Device | Input: Male Connector | Description | Input: Pin | Cable Color | Output: Female Connector | Output: Pin | Cable-typ (Length) | Comment | NTC number |
|---|---|---|---|---|---|---|---|---|---|
| T-Regler 1 | Sub-D-15 (1) | PE 2 | 1 | Yellow + Grey | Sub-D-9 | 3 | 8×0.14 (3m) | Use two wires for each Input-pin. Each Output-pin have four wires! | |
| PE 2 | 2 | Brown + Green | 3 | ||||||
| PE 1 | 3 | Blue + Pink | 8 | Use two wires for each Input-pin. Each Output-pin have four wires! | |||||
| PE 1 | 4 | White + Red | 8 | ||||||
| RUNTEN_MESS | 7 | Pink | Sub-D-37 | 3 | 6×0.14 (3m) | NTC 2 | |||
| ROBEN_MESS | 8 | White | 16 | NTC 16 | |||||
| N47 | 12 | Green | 21 | NTC 2 | |||||
| N48 | 14 | Grey | 34 | NTC 16 | |||||
| T-Regler 2 | Sub-D-15 (2) | PE 2 | 1 | Yellow + Grey | Sub-D-9 | 2 | 8×0.14 (3m) | Use two wires for each Input-pin. Each Output-pin have four wires! | |
| PE 2 | 2 | Brown + Green | 2 | ||||||
| PE 1 | 3 | Blue + Pink | 7 | Use two wires for each Input-pin. Each Output-pin have four wires! | |||||
| PE 1 | 4 | White + Red | 7 | ||||||
| RUNTEN_MESS | 7 | Pink | Sub-D-37 | 6 | 6×0.14 (3m) | NTC 1 | |||
| ROBEN_MESS | 8 | White | 18 | NTC 11 | |||||
| N47 | 12 | Green | 24 | NTC 1 | |||||
| N48 | 14 | Grey | 36 | NTC 11 | |||||
| T-Regler 3 | Sub-D-15 (3) | PE 2 | 1 | Yellow + Grey | Sub-D-9 | 1 | 8×0.14 (3m) | Use two wires for each Input-pin. Each Output-pin have four wires! | |
| PE 2 | 2 | Brown + Green | 1 | ||||||
| PE 1 | 3 | Blue + Pink | 6 | Use two wires for each Input-pin. Each Output-pin have four wires! | |||||
| PE 1 | 4 | White + Red | 6 | ||||||
| RUNTEN_MESS | 7 | Pink | Sub-D-37 | 8 | 6×0.14 (3m) | NTC 8 | |||
| ROBEN_MESS | 8 | White | 15 | NTC 4 | |||||
| N47 | 12 | Green | 26 | NTC 8 | |||||
| N48 | 14 | Grey | 33 | NTC 4 | |||||
| Out-of-Loop-Monitoring-Box | Sub-D-25 | NTC 3 | 1 | Yellow | Sub-D-37 | 16×0.14 (3m) | NTC 3 | ||
| 14 | Green | ||||||||
| NTC 5 | 2 | Green/White | NTC 5 | ||||||
| 15 | Brown | ||||||||
| NTC 6 | 3 | Grey | NTC 6 | ||||||
| 16 | Green/Brown | ||||||||
| NTC 7 | 4 | Pink | NTC 7 | ||||||
| 17 | White | ||||||||
| NTC 9 | 5 | Blue | NTC 9 | ||||||
| 18 | Blue/Red | ||||||||
| NTC 10 | 6 | Yellow/White | NTC 10 | ||||||
| 19 | Yellow/Brown | ||||||||
| NTC 12 | 7 | Red | NTC 12 | ||||||
| 20 | Pink/Grey | ||||||||
| NTC 13 | 8 | Black | NTC 13 | ||||||
| 21 | Purple | ||||||||
| NTC 14 | 9 | Yellow | 16×0.14 (3m) | NTC 14 | |||||
| 22 | Grey | ||||||||
| NTC 15 | 10 | Yellow/Brown | NTC 15 | ||||||
| 23 | Green/White | ||||||||
| NTC 17 | 11 | Yellow/White | NTC 17 | ||||||
| 24 | Green/Brown | ||||||||
| NTC 18 | 12 | Purple | NTC 18 | ||||||
| 25 | Black | ||||||||
| free | 13 | not used / not connected! |
Example of soldering
Schirmung der Kable an die Buchse auf der Seite des Reglers/Sub-D-15 Konnector löten. Und die anderen Sub-D-15 Pins mit Schrumpfschlauch isolieren. Durchsichtigen Schrumpfschlauch verwenden!
