meta data for this page
Translations of this page:
- en
This is an old revision of the document!
Labelling of the cables
Labelling of the T-Regler cable
Peltierelemente werden an der Oberseite warm, wenn Output-Pins 3,2 sowie 1 an positiver Spannung angeschlossen ist.
Benutzt wird der Kabeltyp:
- Für Peltierelemente: LAPP Kabel Stuttgart Unitronic LIYCY 8×0.14; Schirmung von alle Adern gleichzeitig
- Für In-loop-NTC´s: LAPP Kabel Stuttgart Unitronic LIYCY 6×0.14; Schirmung von alle Adern gleichzeitig
- Für Out-of-loop-NTC´s: LAPP Kabel Stuttgart Unitronic LIYCY 16×0.14; Schirmung von alle Adern gleichzeitig
| Device | Input: Male Connector | Description | Input: Pin | Output: Female Connector | Output: Pin | Cable-typ (Length) | Comment | NTC number |
|---|---|---|---|---|---|---|---|---|
| T-Regler 1 | Sub-D-15 (1) | PE 2 | 1 | Sub-D-9 | 3 | 8×0.14 (3m) | Use two wires for each Input-pin. Each Output-pin have four wires! | |
| PE 2 | 2 | 3 | ||||||
| PE 1 | 3 | 8 | Use two wires for each Input-pin. Each Output-pin have four wires! | |||||
| PE 1 | 4 | 8 | ||||||
| RUNTEN_MESS | 7 | Sub-D-37 | 3 | 6×0.14 (3m) | NTC 2 | |||
| ROBEN_MESS | 8 | 16 | NTC 16 | |||||
| N47 | 12 | 21 | NTC 2 | |||||
| N48 | 14 | 34 | NTC 16 | |||||
| T-Regler 2 | Sub-D-15 (2) | PE 2 | 1 | Sub-D-9 | 2 | 8×0.14 (3m) | Use two wires for each Input-pin. Each Output-pin have four wires! | |
| PE 2 | 2 | 2 | ||||||
| PE 1 | 3 | 7 | Use two wires for each Input-pin. Each Output-pin have four wires! | |||||
| PE 1 | 4 | 7 | ||||||
| RUNTEN_MESS | 7 | Sub-D-37 | 6 | 6×0.14 (3m) | NTC 1 | |||
| ROBEN_MESS | 8 | 18 | NTC 11 | |||||
| N47 | 12 | 24 | NTC 1 | |||||
| N48 | 14 | 36 | NTC 11 | |||||
| T-Regler 3 | Sub-D-15 (3) | PE 2 | 1 | Sub-D-9 | 1 | 8×0.14 (3m) | Use two wires for each Input-pin. Each Output-pin have four wires! | |
| PE 2 | 2 | 1 | ||||||
| PE 1 | 3 | 6 | Use two wires for each Input-pin. Each Output-pin have four wires! | |||||
| PE 1 | 4 | 6 | ||||||
| RUNTEN_MESS | 7 | Sub-D-37 | 8 | 6×0.14 (3m) | NTC 8 | |||
| ROBEN_MESS | 8 | 15 | NTC 4 | |||||
| N47 | 12 | 26 | NTC 8 | |||||
| N48 | 14 | 33 | NTC 4 | |||||
| Out-of-Loop-Kiste | Sub-D-25 | NTC | 1 | Sub-D-37 | 16×0.14 (3m) | |||
| 2 | ||||||||
| NTC | 3 | |||||||
| 4 | ||||||||
| NTC | 5 | |||||||
| 6 | ||||||||
| NTC | 7 | |||||||
| 8 | ||||||||
| NTC | 9 | |||||||
| 10 | ||||||||
| NTC | 11 | |||||||
| 12 | ||||||||
| NTC | 13 | |||||||
| 14 | ||||||||
| NTC | 15 | |||||||
| 16 | ||||||||
| NTC | 17 | 16×0.14 (3m) | ||||||
| 18 | ||||||||
| NTC | 19 | |||||||
| 20 | ||||||||
| NTC | 21 | |||||||
| 22 | ||||||||
| NTC | 23 | |||||||
| 24 | ||||||||
| free | 25 | not used / not connected! |
Example of soldering
Schirmung der Kable an die Buchse auf der Seite des Reglers/Sub-D-15 Konnector löten. Und die anderen Sub-D-15 Pins mit Schrumpfschlauch isolieren. Durchsichtigen Schrumpfschlauch verwenden!
