meta data for this page
  •  

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision		Previous revision
groups:mg:project_ptb-cavity:incoupling_breadboard-board [2017/08/07 15:26] – pkoopmanngroups:mg:project_ptb-cavity:incoupling_breadboard-board [2017/09/05 13:03] (current) – ssauer
Line 3: Line 3:
 Alle Dokumente befinden sich im AFS unter: \\AFS\.iqo.uni-hannover\projects\magnesium\Projekte\PTB Ultrastable laser\PTB Files\Breadboard \\ Alle Dokumente befinden sich im AFS unter: \\AFS\.iqo.uni-hannover\projects\magnesium\Projekte\PTB Ultrastable laser\PTB Files\Breadboard \\
 Breadboard: M4-Löcher im Abstand von 15 mm \\ Breadboard: M4-Löcher im Abstand von 15 mm \\
-Strahlhöhe: 29 mm (zu Beginn) +Strahlhöhe: 29 mm (zu Beginn), 57 mm (zwischen Fahrstuhl und Einkoppelspiegel), 43 mm (vor PDH-diode)\\ 
 +\\
 Anforderungen: Anforderungen:
   * jedes Element verschiebbar, sodass keine Reflexe zurück ins System reflektiert werden   * jedes Element verschiebbar, sodass keine Reflexe zurück ins System reflektiert werden
Line 12: Line 13:
   * Halter: zur Dreipunktlagerung auf Unter   * Halter: zur Dreipunktlagerung auf Unter
   * Winkel bei den Spiegeln wurden nicht größer als im Datenblatt vorgeschrieben gewählt   * Winkel bei den Spiegeln wurden nicht größer als im Datenblatt vorgeschrieben gewählt
-  * +
  
 ===== Version 5 ===== ===== Version 5 =====
Line 26: Line 27:
 ===== Version 4 ===== ===== Version 4 =====
   * sending light upwards is not good, "elevator" is better   * sending light upwards is not good, "elevator" is better
-  * PDH-PD and RAM-PD: good, that there is the possibility to place isolators in front of them if they are needed+  * PDH-diode and RAM-diode: good, that there is the possibility to place isolators in front of them if they are needed
   * Breadboard bigger for more space   * Breadboard bigger for more space
   * Vakuum-ground can be connected to vakuum-top by the breadboard   * Vakuum-ground can be connected to vakuum-top by the breadboard
Line 36: Line 37:
  
 ===== Version 3 ===== ===== Version 3 =====
-  * RAM-PD: no mirror in front of it for adjusting the laser beam+  * RAM-diode: no mirror in front of it for adjusting the laser beam
   *    * 
 {{:groups:mg:project_ptb-cavity:v3_-_oben.png?400|}} {{:groups:mg:project_ptb-cavity:v3_-_oben.png?400|}}
Line 53: Line 54:
 ===== Version 1 ===== ===== Version 1 =====
   * optical components were missing (cubes for adjusting the light)   * optical components were missing (cubes for adjusting the light)
-  * PDH and RAM-diode shouldn't be positioned after the same cube, so that they don't influence each other. So te RAM-diode was positioned direktly before the isolator+  * PDH-diode and RAM-diode shouldn't be positioned after the same cube, so that they don't influence each other. So te RAM-diode was positioned direktly before the isolator
 {{:groups:mg:project_ptb-cavity:v1_-_oben.png?400|}} {{:groups:mg:project_ptb-cavity:v1_-_oben.png?400|}}
 {{:groups:mg:project_ptb-cavity:v1_-_vorne.png?400|}} {{:groups:mg:project_ptb-cavity:v1_-_vorne.png?400|}}